JooMix

Style Switcher

Layout options
  • Boxed Layout
  • Full Width Layout
Primary Color

11 Unit, 6the floor , Jalal Ale Ahmad High Way, Tehran , Iran

+98-21 8838 4292

POLYETHYLENE

 POLYETHYLENE (HDPE)

1-Properties

HDPE is known for its large strength-to-density ratio. The density of HDPE can range from 0.93 to 0.97 g/cm3 or 970 kg/m3. Although the density of HDPE is only marginally higher than that of low-density polyethylene, HDPE has little branching, giving it stronger intermolecular forces and tensile strength than LDPE. The difference in strength exceeds the difference in density, giving HDPE a higher specific strength. It is also harder and more opaque and can withstand somewhat higher temperatures (120 °C/ 248 °F for short periods, 110 °C /230 °F continuously). High-density polyethylene, unlike polypropylene, cannot withstand normally required autoclaving conditions. The lack of branching is ensured by an appropriate choice of catalyst (e.g., Ziegler-Natta catalysts) and reaction conditions.

2-Production

 High-density polyethylene (HDPE) or polyethylene high-density (PEHD) is a polyethylene thermoplastic made from petroleum. It is sometimes called "alkathene" or "polythene" when used for pipes. With a high strength-to-density ratio, HDPE is used in the production of plastic bottles, corrosion-resistant piping, geomembranes, and plastic lumber. HDPE is commonly recycled, and has the number "2" as its resin identification code

3-Applications

HDPE is resistant to many different solvents and has a wide variety of applications:

  • Swimming pool installation
  • 3-D printer filament
  • Arena Board (puck board)
  • Backpacking frames
  • Ballistic plates
  • Banners
  • Bottle caps
  • Chemical-resistant piping
  • Coax cable inner insulator
  • Food storage containers
  • Fuel tanks for vehicles
  • Corrosion protection for steel pipelines
  • Personal Hovercraft; albeit too heavy for good performance
  • Electrical and plumbing boxes

MCH3713 - MFI 0.1 - Density0.937

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
MCH3713 0.1 0.937 FILM Bags Download

F7000 - MFI 0.04 - Density 0.952

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
F7000 0.04 0.952 FILM Enhanced ultra thin film Download

CRP100N - MFI 0.22 - Density0.948

Grade MFI ( 190˚ C/ 21.6 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
CRP100N 0.22 0.948 Extrusion Top quality PE100 pressure Download

EX5 - MFI 0.28 - Density0.949

Grade MFI ( 190˚ C/ 5 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
EX5 0.28 0.949 FILM Film extrusion /carrier bags Download

BL4 - MFI 0.35 - Density0.951

Grade MFI ( 190˚ C/ 5 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
BL4 0.35 0.951 Blow High stiffness and impact good stress cracking resistance Download

H0035 - MFI 0.28-0.43 - Density0.959

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
0035 0.28-0.43 0.959 Blow General purpose houseware toys Download

S 5000 - MFI 0.82 - Density0.95

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
S 5000
0.82 0.95 Extrusion Fishing nets, insect screens, ropes, cloth Download

BL3 - MFI 1.2 - Density0.954

Grade MFI ( 190˚ C/ 5 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
BL3 1.2 0.954 Blow Small blow moulding / bottles Download

HD5030SA - MFI 2.2 - Density0.950

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
HD5030SA 2.2 0.950 Injection Closures with Torque Free Property Download

EX2 - MFI 2.5 - Density0.956

Grade MFI ( 190˚ C/ 21.6 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
EX2 2.5 0.956 Extrusion Production of monofilaments with high tensile strength Download

6040UA - MFI 3.7 - Density0.96

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
6040UA 3.7 0.96 Injection Shipping container Download

3840UA - MFI 4 - Density0.938

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
3840UA 4 0.938 Roto Rotational moulded items with good stiffness Download

EX3 80S - MFI 4 - Density0.945

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
EX3-80S 4 0.938 Extrusion PE-80 Pressure pipe Download

HI0500 - MFI 4-6 - Density0.963

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
HI0500 4-6 0.963 Injection Crates- Industrial parts . Thick wall parts Download

52505UV - MFI 5 - Density0.952

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
52505UV 5 0.952 Injection Containers Download

2200J - MFI 5.2 - Density0.964

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
2200J 5.2 0.964 Injection Technical and Industrial Part /Shipping container/Fish crates/Storing cases Download

60505UV - MFI 5.5 - Density0.957

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
60505UV 5.5 0.957 Injection injection molding grade . Crates Download

EX3 100S - MFI 6.2 - Density0.945

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
EX3-100S 6.2 0.945 Extrusion Drinking water and gas pipes Download

60507 - MFI 7.5 - Density0.958

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
60507 7.5 0.958 Injection Crates /  injection molding grade Download

I3 - MFI 8 - Density0.957

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
I3 8 0.957 Injection Crates Engineering parts-Closures Download

FH5110 - MFI 10 - Density0.950

Grade MFI ( 190˚ C/ 21.6 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
HF5110 10 0.950 FILM Extrusion, film, blown Download

I4 - MFI 11 - Density0.944

Grade MFI ( 190˚ C/ 5 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
I4 11 0.944 Injection For thick walled Download

HD52511 - MFI 11 - Density0.952

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
HD52511 11 0.952 Injection Injection molding frad Download

HD60511 - MFI 11 - Density0.96

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
HD60511 11 0.96 Injection housewares and toys applications Download

HD52518 - MFI 18 - Density0.952

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
HD52518 18 0.952 Injection House ware, hall fludity Download

HD5620EA - MFI 20 - Density0.956

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
HD5620EA 20 0.956 Injection Toyes, House ware, Thin walled containers Download

 

POLYETHYLENE (LDPE)

1-Properties

LDPE is defined by a density range of 0.910–0.940 g/cm3. It is not reactive at room temperatures, except by strong oxidizing agents, and some solvents cause swelling. It can withstand temperatures of 80 °C continuously and 95 °C for a short time. Made in translucent or opaque variations, it is quite flexible and tough. LDPE has more branching (on about 2% of the carbon atoms) than HDPE, so its intermolecular forces (instantaneous-dipole induced-dipole attraction) are weaker, its tensile strength is lower, and its resilience is higher. Also, because its molecules are less tightly packed and less crystalline due to the side branches, its density is lower.

2-Production

Low-density polyethylene (LDPE) is a thermoplastic made from the monomerethylene. It was the first grade of polyethylene, produced in 1933 by Imperial Chemical Industries (ICI) using a high pressure process via free radical polymerization. Its manufacture employs the same method today. The EPA estimates 5.7% of LDPE (recycling number 4) is recycled.Despite competition from more modern polymers, LDPE continues to be an important plastic grade. In 2013 the worldwide LDPE market reached a volume of about US$33 billion.

3-Applications

 LDPE is widely used for manufacturing various containers, dispensing bottles, wash bottles, tubing, plastic bags for computer components, and various molded  laboratory equipment. Its most common use is in plastic bags.

2420D - MFI 0.25 - Density 0.923

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
2420D 0.25 0.923 Blown Film Bags & Pouches Download

2130- MFI 0.3 - Density 0.921

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
2130 0.3
0.921 FILM Heavy Duty Film Download

2100 - MFI 0.3 - Density 0.921

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
2100 0.3 0.921 Blown Film industrial sacks Download

LH0075 - MFI 0.75 - Density 0.921

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
LH0075 0.75 0.921 FILM Carrier bags,shrink film Download

2102TN42 - MFI 1.9 - Density 0.921

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
2102TN42 1.9 0.921 FILM food packaging Download

2102TX00 - MFI 1.9 - Density 0.921

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
2102TX00 1.9 0.921 Blown Film pouches,bags,liners and lamination film Download

LTM2119X LF190 - MFI 1.9 - Density 0.921

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
LTM2119X LF190 1.9 0.921 FILM GP FILM Download

2420H - MFI 1.9 - Density 0.921

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
2420H 1.9 0.924 FILM Bags & Pouches Download

0200- MFI 2 - Density 0.919

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
0200 2 dg/min
0.919 extrusion mainly industrial films for agriculture Download

 

POLYETHYLENE (LLDPE)

1-Properties

Linear low-density polyethylene (LLDPE) is a substantially linear polymer (polyethylene), with significant numbers of short branches, commonly made by copolymerization of ethylene with longer-chain olefins. Linear low-density polyethylene differs structurally from conventional low-density polyethylene (LDPE) because of the absence of long chain branching. The linearity of LLDPE results from the different manufacturing processes of LLDPE and LDPE. In general, LLDPE is produced at lower temperatures and pressures by copolymerization of ethylene and such higher alpha-olefins as butene, hexane, or octane. The copolymerization process produces a LLDPE polymer that has a narrower molecular weight distribution than conventional LDPE and in combination with the linear structure, significantly different rheological properties.

2-Production

The production of LLDPE is initiated by transition metal catalysts, particularly Ziegler or Philips type of catalyst. The actual polymerization process can be done either in solution phase or in gas phase reactors. Usually, octane is the co-monomer in solution phase while butane and hexane are copolymerized with ethylene in a gas phase reactor. LLDPE has higher tensile strength and higher impact and puncture resistance than does LDPE. It is very flexible and elongates under stress. It can be used to make thinner films, with better environmental stress cracking resistance. It has good resistance to chemicals. It has good electrical properties. However, it is not as easy to process as LDPE, has lower gloss, and narrower range for heat sealing

3-Applications

LLDPE has penetrated almost all traditional markets for polyethylene; it is used for plastic bags and sheets (where it allows using lower thickness than comparable LDPE), plastic wrap, stretch wrap, pouches, toys, covers, lids, pipes, buckets and containers, covering of cables, geomembranes,and mainly flexible tubing. In 2013, the world market for LLDPE reached a volume of $40 billion.

AA209 - MFI 0.9 - Density 0.92

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
209 AA 0.9 0.92 Blown Film Liner bags, builders reel, Co-extrusion Download

209KJ - MFI 0.9 - Density 0.92

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
209KJ 0.9 0.92 Blown Film Liner bags, deep freeze film Download

220AA - MFI 2.2 - Density 0.92

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
220AA 2.2 0.92 Cast Film Stretch wrap, Oriented Tape Download

220KJ - MFI 2.4 - Density 0.92

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
220KJ 2.4 0.921 Blown Film food packaging Download

32604UV - MFI 4 - Density0.932

Grade MFI ( 190˚ C/ 2.16 Kg ) Density(gr/cm3) Application Typical Application Data Sheet
32604UV 4 0.932 Roto all applications which need a good balance among moldability Download

 

Petrobourse

11 Unit, 6th floor , Jalal Ale Ahmad High Way, Tehran , Iran

by phone: +98-21 8838 4292

by e-mail: Info@azgint.com

or fill in the form on our contact page

Join our Newsletter

Vestibulum ante ipsum primis in faucibus orci luctus et ultrices posuere cubilia Curae; Etiam id enim egestas, congue est id, hendrerit magna.